COMMON TECHNICAL BREAKDOWN ISSUES OF WATER JET LOOM(2)

TODAY, WE ARE GOING TO INTRODUCE HOW TO MAINTAIN THE CUTTERS OF WATER JET LOOM AS BELOW:

RH/LH CUTTERS: THE CUTTERS WILL GET WORN EASILY DUE TO MAL-ADJUSTMENT OF TOLERANCE BETTER BLADES, AS WELL AS THAT OF BEARING AND AXIS. WHEN SETTING THE UP AND DOWN SIDE BLADES, THE INTERSECTION ANGLE SHOULD NOT BE SET BIG, OTHERWISE THE TWO BLADES WILL JOINT TOO TIGHT AND GET WORN EASILY. WHEN SETTING THE CUTTER, MAKE IT WILL CLASH THE REED. WHEN USING FEELER, FOLLOWING WAY IS RECOMMENDED FOR LH CUTTER: OPEN A GAP (A BIT WIDER THAN THE CUTTER THICKNESS) IN THE REED WHERE FACES THE CUTTER, THEN FIX THE CUTTER-CAM AT 180°. TWO ADVANTAGES FOR SUCH SETTING: 1. AVOID COLLISION BETWEEN REED AND CUTTER; 2. CREATE STABLE WASTE-YARN LINE. FROM TIME TO TIME, THE ANGLE OF THE CUTTER AND RELATED FIXTURE SHOULD BE CHECKED, IN ANY SLACK-OFF IS THERE. 

COMMON TECHNICAL BREAKDOWN ISSUES OF WATER JET LOOM(1)

FROM TIME TO TIME,WE ARE GOING TO BRING YOU IDEAS ABOUT HOW TO WROK WITH WATER JET LOOM IN A SOUND WAY:

1.       WATER JET LOOM IS RUNNING IN VERY TOUGH SITUATION (HUMID, HEAT, HIGH SPEED, 24HR NON-STOP) AND REQUIRES HIGH WORKING PRECISION OF PARTS, THEREFORE, SOME BREAKDOWN MAY HAPPEN AFTER LONG TIME RUNNING. THERE ARE SEVERAL TYPES OF BREAKDOWN WHICH IMPACT THE PERFORMANCE OF THE MACHINE IN DIFFERENT WAYS. SOME ARE DUE TO LONG-TERM USE, LIKE: THE CHANGING JET DIRECTION OF NOZZLE; SOME ARE CAUSED DUE TO OTHER ELEMENTS, LIKE: ONE TYPE OF PUMP WATER PRESSURE CAN NOT MEET ALL REQUIREMENTS OF DIFFERENT TYPES OF FABRIC; IT HAS TO BE ADJUSTED ACCORDINGLY.

2.       THE MAINTENANCE&IMPROVEMENT OF COMMON BREAKDOWN

2.1 TOP LAW: SUPPOSE THERE IS BREAKDOWN HAPPENING TO ONE PART, THE SOLUTION THAT SIMPLY REPAIR OR MAINTAIN THE SAID IS NOT ENOUGH; MOREOVER, ONE HAS TO FIND OUT THE FACTOR CAUSES SUCH

MALFUNCTION, ELIMINATE SUCH FACTOR PERMANENTLY TO AVOID REPEATING BREAKDOWN. WE ARE NOT TALKING ABOUT SIMPLE REPLACEMENT OF THE PART, BUT IMPROVE IT ACCORDING TO ITS WORKING THEORY OR FEATURES. A GOOD MECHANIC SHOULD HAVE ENOUGH KNOWLEDGE ABOUT THE WORKING THEORY OF EACH PART.

MORE TO CONTINUE........

REGARDS

ROBERT

www.waterjetloom.biz

CHINA YUAN DEVALUING BOOST EXPORT OF TEXTILE PRODUCTS

RECENTLY, we have seen the devaluation of China Yuan from 6.2 to 6.4.This will have positive effect on export of textile products. According to report of our domestic weavers, they are expecting a 25% sale increase in September compared to the month of August,However, they also marked no plan of increase production of the water jet loom plant, and first concern will be to consume huge stock since last few months.

STOCK IN JIAXING MINGYE  TEX LTD

WHY WE SHOULD GO WITH WATER JET LOOM

Dear Viewers:
     Many are asking: what is the best machine to weave polyester related fabric.
     Well, definitely,water jet loom will take the credit, though many are complaining the water pollution issue.
     But, pls note CAR is producing air pollution....
     For every technology, GOOD always goes with NOT-GOOD. (RECENT ROBOT KILL WORKERS AT VOLKSWAGEN?)
     The point is that a possible way to work with water jet loom shall be maintained.
     So why we should go with water jet loom, the exact reason?

     Well, we can justify it in three points:
     1. Pretty Low initial investment for water jet loom machinery itself.
        Compared to more sophisticated machinery like Air Jet Loom or Rapier Loom. The investment for water jet loom is relatively lower to the point that the cost of one set of Air Jet loom or Rapier Loom equals 2 sets Japan-make water jet loom or even 6 sets China-make water jet loom.
        And this is only about weaving machine itself; another is also to mentioned that is PRE-WEAVING PREPARATORY like warping, sizing and TFO etc.
     2. Super-high Productivity. In terms of weaving, water jet loom is very suitable to weave polyester fabric in high speed and with different shedding like: plain, cam, dobby and Jacquard for versatile pattern design. In the meantime, water jet loom consumes less power compared to rapier loom and air jet loom.
     3. Lower Labor Cost.For most East-Asia countries,A shortage of skilled operator is headache, such as India, many weaving unit is closed periodically for shortage of operators. 
        Now with standard, easy-operation and high-efficient water jet loom, this problem is kind of solved.
        Water Jet Loom has very high working efficiency like 98%, it means less stop rate of machine. It makes it possible for one weaver to handle 6-24 sets of machines at one time; therefore labor cost is cut down.
     In Conclusion,if one is thinking to weave polyester related fabric, water jet loom is absolute the best choice.

Regards
Robert